For Uber Drivers

Product review: Bestrix Universal CD Slot Car Mount Phone Holder

I’ve been driving a while now. As part of that, obviously I needed to have a holder for my phone; a lot of people including law enforcement tend to frown on either holding the phone while you drive or having it in your lap, and for good reason too. Unfortunately the holder I was using – a magnetic one – failed on me a little while ago, during a ride in fact. The magnet was fine, but the glue that held it to the back of the phone couldn’t hold against the magnet. After it worked so well previously, I got a replacement magnet for the same system. Initially it was OK, but I suspect the residual glue left behind from the old magnet stopped the new magnet from sticking properly, and so the pull from the auxiliary cable used was enough to pull the phone off the magnet.

So I went shopping. I thought I’d found the replacement made by the same company: another vent-mounted holder that held the phone around its waist rather than via a magnet on its back. Unfortunately the rubber grip was not quite grippy enough to hold the phone permanently. It was good enough as a temporary measure, especially using the volume know for the radio as a rest for the bottom of the phone, but it I knew it was going to annoy the ever-living you-know-what out of me to always be adjusting it to make sure it didn’t fall out. So I went shopping again.

(I’m purposefully not naming the mounts that didn’t work or the company that makes them. The first one did the job it was supposed to for a long time, and if I’d not needed a quick fix I probably wouldn’t have got the second one in the first place. The company makes good stuff, and I’m actually using some of it to put this post up. Though it caused me some grief, I’m not going to name and shame them. At least, not this time.)

I went looking on Amazon for car phone mounts. Because of the issues I’d had, I wanted to avoid a magnetic mount or one that otherwise stuck to the back of the phone. I wanted a cradle, and not just around the sides of the phone but along the bottom. With my car, a mount attached to the windshield won’t work because the phone would be too far away from the audio connection and cigarette lighter port to charge the phone. Also, it would be too far away from my hands to be able to actually use, let alone be plugged into anything. I knew from previous attempts that trying to mount anything to the dash itself would be problematic. The only things I’d seen that would work would be a mount attaching to one of the vents, which is what I’d been using up until then.

Bestrix Phone Holder in situ

The Bestrix Universal CD Slot Car Mount Phone Holder holding my phone in my car, with both an aux and a lightning cable attached

Which is when I saw this: the Bestrix Universal CD Slot Car Mount Holder. I know I don’t use the CD player in my car and I suspect that there aren’t too many others out there that do either, so using that slot in the dash for something else is not a problem. It’s basically a somewhat semi-circular base that sticks out from the CD slot, with an elbow-like tube that sticks up and out (or down and out depending on the orientation) to where the cradle itself is mounted. The cradle is mounted on a ball joint, so the phone can be rotated through 360° and the angle of display can be adjusted as needed. It hooks into the CD slot via three flat prongs, the middle of which is at the end of a switch to push it down (or up) to hold the whole thing in place. In case you can’t tell from my optional explanations in parentheses, this can be mounted facing either “up” or “down”, with the phone either above or below the base.

The cradle itself holds the phone on both sides and at the bottom. (This assumes you’re using the phone in its portrait orientation, otherwise it would be top, bottom and either left or right as is your preference.) The bottom claw can be adjusted up or down from the rest of the cradle, and stays in place until the bottom button behind the cradle is held down. You squeeze the side claws in towards the phone when its in the cradle, ensuring it stays securely mounted until you press and hold the release button at the top of the backside of the cradle. If you’re used to a magnetic holder, changing to this will be just the tiniest bit frustrating to get used to, because you won’t be able to instantly attach or detach the phone from the mount. However the flip side of that means that the phone won’t move around or slip out of its place accidentally – in my mind, its well worth the trade off, especially when this one becomes what I’m used to.

I can’t speak for other models of phones, but my iPhone 6s fits nicely even with cables plugged into both the lightning and aux ports. The two prongs for the bottom claw sit either side of the lighting cable, with a little bit of clearance either side to limit the ability of the phone to wiggle even if you have the side claws loose. If for some reason you want to switch from portrait to landscape mode, the screw holding the ball joint can be tightened to just the right amount to allow you to spin the phone around to the new orientation, but manage to hold it still once its been repositioned. And as a special note to Uber drivers: the base of the mount and the positioning of the phone can help to stop front seat passengers from fiddling with your radio without asking because it will probably block the display and controls.

Installation is a breeze. The only issue I had was attaching the cradle to the plate it sits on, and even that was a minor one where I was concerned I was going to break something trying to snap it into place. To be fair, its the sort of fear I tend to get most of the time when I’m assembling things. It came with instructions in the box, and a guide was emailed to me within a day of ordering it from Amazon. (I didn’t use them myself, but I assume they would’ve been helpful if needed.) It comes with three pads of varying thicknesses that are able to be attached to the middle prong used to hold the mount in the CD slot. I didn’t need to use mine, but if I had a wider opening for the CD player I might’ve needed to attach one of them to keep it in place.

If you’re looking to replace an existing mount, or need to install one for your car – and have a CD slot that’s not being used – then this mount is a great choice. It doesn’t cost an arm and a leg, installs easily and does the job exactly as its supposed to.

This slideshow requires JavaScript.

Disclaimer: This isn’t a paid review, I bought the mount with my own money, with the only benefit of doing so being the tax deduction of any business purchase. That being said, if you follow any of the links to Amazon on this page and make a purchase while on the site, I’ll get a small percentage of the sale. It won’t cost you anything extra, and you can purchase anything you like from the site; it doesn’t have to be the mount I’m reviewing, or any other mount, just follow a link, search for anything your wanting to get and buy it the same way you would any other time on Amazon. Making Amazon purchases through one of these links is a great way of supporting the blog without having to donate, subscribe or otherwise pay extra money, and helps to ensure I’ve got time to write these posts. Thank you for your support, and if you’re in Sydney, I might just see you on the road!

Advertisements

What do you think about all this?